Step Tutorial for Installing a Bathtub
Step Tutorial for Installing a Bathtub
Blog Article
The content which follows pertaining to Tools You Need to Install a New Bathtub is definitely insightful. Read on and draw your own personal conclusions.
Installing a bath tub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably hard project. If the old bathtub is easily obtainable, the project can move quickly; if you have to open up a wall to get rid of the old bathtub and also place the new bathtub, the task is much harder. In either case, the project is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have actually qualified on your own for the work as well as are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is far better to take into consideration using one prior to you start. Chances are you might need a professional plumber to make tube links.
This article will aid you mount a new bathtub in your restroom if you have currently purchased a new bathtub as well as do not need to alter the setup of your previous water supply pipelines.
Your devices and also product checklist ought to consist of the following:
Getting ready for the Installment
To start with, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the limited accessibility that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been gotten rid of, utilize the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the bathtub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water supply and also examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill up the tub and additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been made use of a minimum of when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing opening in the bath/basin ensuring that the washing machines are in place between the tap as well as the sink. Protect the tap in position with the manufacturer provided backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal tap ports. The former kind must be linked to the tap ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, causing the water to permeate the wall in between the bath as well as the tiling, bring about complications with moisture and feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealer can split relatively very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the market. It is advisable to fit the tiles utilizing waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very inquisitive about Tools You Need to Install a New Bathtub and I really hope you liked the new blog post. Those who liked our blog post kindly do not forget to share it. Thank you for your time. Visit again soon.
Urgent plumbing? Call us. Report this page